Edelbrock Pro-Tuner Spécifications télécharger pdf

Catalog #3615, 3616

Rev. 6/07 - RS/mc

Brochure #63-3615Page 1 of 4

PRO-TUNER EFI DISTRIBUTORS WITH CAM-SYNC

Catalog #3615, 3616

INSTALLATION INSTRUCTIONS

PLEASE study these instructions carefully before beginning this installation. Most installations can be accomplished with common tools and

procedures. However, you should be familiar with and comfortable working on your vehicle. If you do not feel comfortable performing this installation,

it is recommended to have the installation completed by a qualified mechanic. If you have any questions, please call our Technical Hotline at:

1-800-416-8628, 7:00 am - 5:00 pm, Pacific Standard Time, Monday through Friday or e-mail us at [email protected]

IMPORTANT NOTE: Proper installation is the responsibility of the installer. Improper installation

will void your warranty and may result in poor performance and engine or vehicle damage.

DESCRIPTION: Pro-Tuner Distributors with Cam-Sync are designed for use with our Victor and Super Victor Pro-Tuner EFI systems. They are also

compatible with other aftermarket EFI management systems. These distributors include a large Ford-style distributor cap, locked out mechanical

advance. and a steel distributor drive gear. Chevrolet applications (only) include adjustable hold down collar to accommodate various deck heights and

intake manifolds. Pro-Tuner distributors also feature a Magnetic Crank Pickup and use a Hall-Effect Cam-Sync Pickup with LED indicator for the

Camshaft Sensor. The Cam-Sync pickup can be adjusted manually or with EFI management software to achieve the proper lead time required by your

ECU. The Cam Sync has a 12” lead and a 3-prong Weatherpak connector. The crank trigger has an 8” lead and 2-prong Weatherpak connector.

APPLICATIONS:

3615 - Small Block (283-400 CID) & Big Block Chevrolet V8 (396-502 CID)

3616 - Pontiac V8 (389-455 CID)

KIT CONTENTS:

❑ 1 Pro-Tuner Distributor

❑ 1 Rotor (MSD #8421)

❑ 1 Distributor Cap (MSD #8408)

❑ 1 Wire Retainer

❑ 2 1.5” Long, Self Tapping Screws

❑ 1 Distributor Gasket

❑ 2 O-Rings (3615 only)

❑ 1 Tube of Assembly Lube

BEFORE BEGINNING INSTALLATION

WARNING: When installing the distributor, make sure to disconnect the vehicle’s battery BEFORE beginning the installation.

NOTE: If the drive gear is ever replaced, you must use a MSD #8531 distributor drive gear due to the .500” diameter drive shaft.

• HALL-EFFECT PICKUP

LED OPERATION: The LED is on whenever the magnet is NOT in front of the pickup. The LED Turns off when the magnet passes over the

center of the pickup (approximately 40°)

(See Figure 1)

Specifications

Accepts 5-18 Volts continuous

Output: Within 1.5 volts on the red wire, and .3 volts above ground

Protected from reverse polarity, short circuit and over voltage

Figure 1 - Hall Effect Sensor

1 2 3 4

Résumé du contenu

Page 1 - INSTALLATION INSTRUCTIONS

Page 2 - Brochure #63-3615Page 2 of 4

Page 3 - Brochure #63-3615Page 3 of 4

Page 4 - Brochure #63-3615Page 4 of 4

Plus de documents pour Accessoires et composants de véhicules automobiles Edelbrock Pro-Tuner

Voir le document Edelbrock Pro-Tuner Guide de l'utilisateur

Edelbrock Pro-Tuner Guide de l'utilisateur (30 pages)

Commentaires sur ces manuels

Pas de commentaire

Edelbrock Pro-Tuner Spécifications

Naviguer en ligne ou télécharger Spécifications pour Accessoires et composants de véhicules automobiles Edelbrock Pro-Tuner. Edelbrock Pro-Tuner Specifications [en] Manuel d'utilisatio

Résumé du contenu

Plus de documents pour Accessoires et composants de véhicules automobiles Edelbrock Pro-Tuner

Commentaires sur ces manuels

Produits connexes et manuels pour Accessoires et composants de véhicules automobiles Edelbrock Pro-Tuner